WhatsApp

Version française en préparation — cette page s'affiche pour l'instant en anglais.

BN-XJ002 Movable Small Scissor Lift – 4,000 kg, 115 mm Profile, No Trench Needed

Profix

BN-XJ002 Movable Small Scissor Lift – 4,000 kg, 115 mm Profile, No Trench Needed

115 mm high, 4,000 kg, and it rolls to whichever car needs it.

Prix sur demande Demander un devis Demander sur WhatsApp
  • SKU BN-XJ002
  • Expédié depuis Sea freight, LCL or FCL, SKD packed
  • Préparation 15–25 days
Droits acquittés : Douane et droits : nos routes DDP incluent les droits et le dédouanement — le prix affiché est le prix payé. Lorsque le droit de 3 € par article s'applique, nous regroupons les articles en lots pour en répartir le coût.

Ce que fait le produit

  • No trench, no foundation, no installation - wheel it into place and work
  • 4,000 kg capacity on a compact 1,460-2,010 mm stretchable platform
  • Movable rollers and associated base, so one lift covers a whole row of cars
  • Two-way approach bridge with flexible driving direction
  • 20 mm thick platform arm - high strength, no permanent deformation
  • Patent safety lock design, pneumatic lock and unlock
  • 24 V safety voltage, default-phase and overload protection to international standard
  • CE certified, Pacific Insurance cover, Ministry of Transportation approved

Caractéristiques & expédition

Lifting Capacity4,000 kg
Lifting Height1,000 mm
Lowest Height115 mm
Platform Length1,460–2,010 mm (stretchable)
Platform Width490 mm
Lifting Timeup 40 s / down 35 s
Power Supply380 V / 220 V
Platform arm thickness20 mm
Rated oil pressure20-25 MPa
Air pressure0.5-0.7 MPa
Control voltage24 V safety voltage
Safety systemPatent safety lock, pneumatic lock and unlock, default-phase and overload protection
InstallationNone - movable, surface use, no trench and no foundation
MobilityMovable rollers with associated base
ApproachTwo-way approach bridge, flexible driving direction
CertificationCE
Control cabinetIncluded

The BN-XJ002 is a movable mid-rise scissor lift. It stands 115 mm off the floor, carries 4,000 kg to a 1,000 mm working height, and moves on its own rollers - no trench, no foundation, no installation.

One lift, every bay
Because nothing is fixed, the XJ002 goes to the car instead of the car coming to the lift. In a tyre shop that means the same unit works its way along a row of vehicles; in a body shop it frees the spray booth, the prep area and the wheel bay from needing their own lift. On a site where the floor cannot be cut - rented units, upper floors, temporary premises - it is often the only option that works at all.

Working height, honestly stated
1,000 mm is wheel, brake, suspension and body-panel height. It is not standing room underneath; if you need to walk under the car, this is the wrong product and the XJ001 or a BDJ lift is the right one. Being clear about that on the page saves a return.

Platforms and approach
The platforms stretch from 1,460 mm to 2,010 mm to suit the vehicle, at 490 mm wide with a 20 mm thick arm that stays rigid under load. A two-way approach bridge lets the car drive on from either end, which matters when the lift is parked between two rows of vehicles rather than in a dedicated bay.

Moving and locking
The unit rolls on castors with an associated base. Move it only when it is unloaded: raise the lift to its high position, remove the rollers after installing it in place, lower it to the lowest position, then connect the hook under the control cabinet to the lift base and lock it before use. The sequence is on the sheet and belongs in the manual - do not skip it.

Safety
A patented safety lock with pneumatic locking and unlocking secures the platforms during work. The control circuit runs on 24 V safety voltage to international standards, with default-phase and overload protection. Stainless steel slide rails keep the travel smooth; hydraulics use imported solenoid valves and sealing components.

Certification
CE certified. Insured by Pacific Insurance Company, Ministry of Transportation certified.

Souvent achetés ensemble